International ServiceMaxx Fleet Pro 2017 Diagnostic And Programming J1939 And J1708 Online Version !
Full Online Installation Service Included !
2 Years PRO License Included !
ServiceMaxx Pro version 44.34 (release date 12-01-2017) – Include Latest Online UpdateÂ
The SERVICEMAXX Fleet Pro application is a fully-featured PC application designed to meet the wide range of diagnostic challenges you face when servicing a mixed truck fleet.
Coverage includes all International electronic engine systems, allowing you to run special tests, change parameters, and view and graph engine data. This is the top-of-the-line tool for fleets. The application updates periodically, enabling you to have the most up-to-date coverage throughout your annual subscription.
Basic Functions
- Read Fault and clear diagnostic fault codes
- View, graph and save engine data
Diagnostic Tests
- KOEO – Key On Engine Off
- KOER – Key On Engine Running
- KOEO – Injector Buzz Test
- KOER – Injector Contribution Test
- Cylinder Cutout Test (EPA 04′ and newer)
- Injector Disable Tests (EPA 04′ and newer)
Display and change configurable Parameters
- Crank Inhibit
- Fan Control
- Idle Shutdown Timer
- Warm-up Device
- Warning and Protection System
- Hydraulic Pressure Governor
- PTO Control
- Radiator Shutter
- Vehicle Speed Limit
- Vehicle Retarder
- Two Speed Axle
- Traction Control
System Requirement
SERVICEMAXX FLEET PRO can be run on most PCs with a least 512 MB RAM (1 GB perferred), 100 MB available hard drive space, and CD-ROM running in the Window® XP operating system. The appropriate interface adapter must be used to communicate with the vechicle.
Recommended Adapters
Nexiq Technologies – USB-Link
NAVCoM (Advanced Vehicle Communication Module)
Dearborn Group Technologies – DPA IV, DPA IV+
Noregon Systems, Inc. – DLA, DLA USB
ServiceMaxx J1708
   Connection / Communication:
       9-Pin Type I (Black)
           Protocol CAN J1708 @ 250K Baud
       9-Pin Type II (Green)
           Protocol CAN J1708 @ 250K Baud
   Engine Detection Target:
       Engine Serial Number
   Supported Legacy Engines (1994 – 2006):
       Pre-MaxxForce Engines
           I63BX:3 Box I6 (1994 – 1997)
           V83BX:3 Box V8 (1994 – 1997)
           i308:DLC I6 (1998 – 2004)
           T444E:DLC V8 (1998 – 2004)
           I313:DLCII I6 (2005 – 2006)
           V128:DLCII V8 (2005 – 2006)
           V126:DLCII V6 (2005 – 2006
         Â
ServiceMaxx J1939
   Connection / Communication:
       9-Pin Type I (Black)
           Protocol CAN J1939 @ 250K Baud
           K-line (MWM Engines)
       9-Pin Type II (Green)
           Protocol CAN J1939 @ 250K Baud
           Protocol CAN J1939 @ 500K Baud (2016 North American engines forward)
           KWP2000 K-line (For MWM Engines)
   Engine Detection Target:
       Engine Calibration ID (Production Calibration only)
       CAT Engines also use Parameter: 88/01
   Supported Engines:
       North American
           v155:MaxxForce 5 (2007 – 2009)
           v134:MaxxForce 7 (2007 – 2009)
           v152:MaxxForce 7 (2010 – 2012)
           v179:MaxxForce 7 (2013 – )
           i326:MaxxForce DT, 9, 10 (2007 – 2009)
           i334:MaxxForce DT, 9 ,10 (2010 – 2012)
           i367:MaxxForce DT, 9, 10 (2013)
           i766:MaxxForce 11, 13 (2008 – 2009)
           i783:MaxxForce 11, 13 (2010 – 2012)
           B764:MaxxForce 11, 13 (2013 – 2013.5)
           i770:MaxxForce 15 (2010 – 2013)
       SCR Engines
           I746:N9, N10 SCR (2014 – )
           B718:N13 SCR (2013 – 2014)
           B745:N13 SCR (2015 – )
       Removed Engines:
           I63BX:3 Box I6 (1994 – 1997)
           V83BX:3 Box V8 (1994 – 1997)
           I308:DLC I6 (1998 – 2004)
           T444E:DLC V8 (1998 – 2004)
           V126:DLCII V6 (2005 – 2006)
           I313:DLCII I6 (2005 – 2006)
           V128:DLC V8 (2005 – 2006)
   Engine list below is with Engineering Access:
       Military Engines
           Mil13:MaxxForce 12.4D
       CAT Engines:
           CT11:CAT CT11/13 (2010 – 2012)
           CT764:CAT CT13 (2013)
           CT15:CAT CT15
           CT718:CAT CT13 SCR (2013 – 2014)
           CT745:CAT CT13 SCR (2015 – )
       Global Engines:
           I341:DLCII I6 Export (2007 – )
           I716:N13 (Euro V)
           MWM:MaxxForce 3.0H (Euro III – P418V50)
           MWM:MaxxForce 7.2/4.8 H (Euro III – P625V13)
           MWM:MaxxForce 7.2/4.8 H (Euro IV – P800V24)
           MWM:MaxxForce 7.2/4.8 H (Euro IV – P800V32)
           MWM:MaxxForce 7.2/4.8 H (Euro V – P1090V52)
           MWM:MaxxForce 3.2 H (Euro III)
           MWM:MaxxForce 3.2 H (Euro IV)
           MWM:MaxxForce 3.2 H (Euro V)
       Engineering Engines:
           B786N13 (2017 – )
       Removed Engines (Did not go into Production):
           I355:MaxxForce 9.3 (Euro V)
Software Fixes:
   Software Lag or Slow response Issue
       Change the way Requested signals are handled.
   ServiceMaxx version 42.18 (release date: 08/05/2015)
       Software Enhancements
           MaxxForce 11/13 (2010 – 2013)
               DOC Efficiency Test (Field Service Access)
           MaxxForce DT/9/10 (2010 – 2013)
               DOC Efficiency Test (Engineering Development)
               Air Management Performance Test (Engineering Development)
               Trip Report
               Remove Trip Report (Not Supported)
           MaxxForce 11/13 (2010-13), N13 SCR (2014 – 2015)
               Stand Alone Real Time Clock
               Time Synchronization Check
               Multi Cylinder Cutout enhancements
               Add Start and End temperatures to Test Results
               Trip Report enhancement
               Remove MaxxForce name from Report Printout
               Correct Reset for Trip Active Regen Count
           N9/N10 SCR (2014 – ), N13 SCR (2013 – 2015)
               DPF Regeneration session
                   Session update (Move Test Inhibitors to Default view)
           N13 SCR (2017) Engineering Access only
               Add database Support: Signals/Parameters/DTCs
           Snapshot recordings enhancement
               Remove Min/Max/Average from recordings
               Remove Negative counter
           History Support (Phase 1)
               Writes Engine information to history.
               Vehicle Identification number
               Engine Serial Number
               Calibration ID
               Customer Password – When entered by user.
           Slow Network Alert
               Popup Alert message if slow Network is detected during software updates.
       Software Fixes
           Signal display and Recording
               Display Proper Symbols
               Display correct value in Graphs
           MaxxForce 11/13 (2010 – 2013), N13 SCR (2014 – 2015)
               Multi Cylinder Cutout enhancements
               Refresh Test Results panel if test is re-started.
               Test Abort Message Correction
               High Pressure Pump Test
               Air Management Test
               Intake Air Heater Test
 without needing a net JAVA internet connection
ServiceMaxx version 43.26 (release date 12-09-2015)
We Are Offering Full Teamviewer Support Service ,
We will Connect To your Pc  And Install The Software For you !
Product Details :
Region: All regions
Type: Diagnostic software
Language:English,Spanish,French,Italian,Russian,German,Denish,Polish,Finnish,Dutch,Norwegian,Portuguese,Japanese,Swedish,Turkish,Hungarian,Korea
OS: WinXP, Vista, Windows7,Windows 8 ,Windows 10
No Hardware Or Cable Included !!!
